PHONE (425) 451-8565

Quiet Wing System

Aircraft Induction Checklist for Quiet Wing System™ High Altitude Performance Kit 737-200 Models

PERFORMANCE FLAP DROOP SYSTEM

PLEASE READ THE FOLLOWING INSTRUCTIONS AND PROVIDE BACK TO US THE FOLLOWING INFORMATION. THIS WILL ASSIST US IN PROVIDING YOU WITH A TIMLEY AND ACCURATE INSTALLATION

The following information is required prior to beginning the Quiet Wing System installation.



Name /
Company		 Checklist
Completed by
Title Phone
Fax Email
1. Quiet Wing System Kit Configuration Number 65QW-780002-500
2. Aircraft Model Number
3. Aircraft Line Number 3a. Variable
4. Registration Tail Number Aircraft Serial Number
5. List the engine models as follows:
Engine No.1 Model No. Engine No.2 Model No.
6. Is your aircraft stage III compliant? Yes No
  a. If yes, which Stage III kit?
7. Does the aircraft have a Performance Data Computer? Yes No
  a. If yes, Make Part Number
8. What is the condition of the Mid Flap to Aft Flap Compression Seal? Check One.
Very Good Good Poor Needs Replacing
9. Verify the following measurements with Flaps extended to 5 degrees; measure the distance between the lower mid flap skin aft edge to the leading edge of the aft flap. Verify dimensions on both the I/B and O/B ends and provide details below:
I/B end O/B end
10. Please provide a hard copy or scanned legible copy via e-mail or CD Rom, of the following document pages:
A. AFM Title page through end of Section 1.
B. Weight and Balance Manual, Title page through end of Section 1.
C. Wiring Diagram Manual, Sections 27, 31 and 32.
11. Please list part number, model number, and position (Capt and F/O) of the current Mach / Airspeed Indicators and Aural Warning Switches.
BOEING MASI P/N OEM P/N S/N (CAPT.)
BOEING MASI P/N OEM P/N S/N (1ST OFF.)
BOEING OVERSPEED LIMIT SENSOR P/N
Standby MASI Indicator: If installed.
BOEING MASI P/N OEM P/N S/N
12. Flap Position Indicator
BOEING MASI P/N OEM P/N S/N
13. Flap Lever Quadrant:
a. Is the flap position indicated with a placard? Yes No
b. Is the flap position indicated with a backlit light plate? Yes No
c. If backlit please confirm Boeing P/N by checking the P/N below:
10-61800-221 10-61800-222 10-61800-144 10-61800-145
14. Please provide digital photographs of the following panels:
A. Cockpit front P1 panel; captains main panel to clearly show the MASI.
B. Cockpit front panel, P2 to clearly show the flap position indicator and surrounding area
C. Cockpit overhead P5 aft panel to clearly show the flap/slat annunciators and override area.
D. Flap lever quadrant to clearly show the flap settings and detents
E. Electronics bay rack E3, and E3-2 shelf (starboard rack), E1 and E1-3 Rack.
F. Flap drive unit located in the right hand wheel well, upper right hand side.
G. Hydraulic lines and fittings running from the flap control unit inboard to the mid section of the aircraft wheel well, include an overall photo taken from the L/H W/well to show the L/gear viewing window over to the FCU.
15. Please provide current Aircraft principle weights:
MRW MTOW MLW MZFW
NOTE: The MASI’s, overspeed switch and flap position indicator need to be sent to QWS to be modified as part of the performance kit. During the modification it may be necessary to perform additional maintenance or incorporate manufacturers service bulletins to bring the indicators up to the correct revision level and to maintain airworthiness. The cost for general maintenance and incorporation of service bulletins is the responsibility of the customer.

Printer Friendly copy of form Here